Bracketing & Fixtures

Part No: 12-1130

Description: For measuring dynamic movements. Includes 2 pcs DM brackets, 4 pcs mounting plates, glue Locktite 4070, 4 pcs screw M6x20, hexagon wrench 5 mm. Delivered in plastic case.

 Note: Measuring unit not included.

Part No.: 12-0013

For direct attachment to shaft or flange; used with all shaft systems. Versatile magnet base with On/Off function and many optional rod mounting possibilities.

Notes: Three sides are magnetic. Offset Bracket (XT) must be used with Magnet Base if used with any XT system (ie. XT440)

Part No.: 12-0045

Used together with detectors, measurement units and laser transmitters where the unit needs to be rotated on a fixed magnetic foot.

Notes: On/Off button, 360° turnable head with two rod mounting possibilities.

Part No.: 12-0742

Tilt table for use with an ES-unit as transmitter, e.g. with the Twist measurement program. This tilt table simplifies and makes the rough alignment of the laser beam quicker. Use the EM-unit as detector, mounted on a regular magnet base.

Note: Magnet base and rods included as pictured.

Part No.: 12-0583

For wind tower flanges. Makes it possible to measure near the edge of a surface.

Notes: Probe does not touch surface. Rods and detector not included.

Part No.: 12-0992

Two magnetic brackets and 4pcs rods 120 mm [4.72”] in small case.

Part No.: 12-1011

For axial mounting on flanges or shafts. With M6 screws working as radial supports, and four super magnets. Used for both the XT Series and the E-Series.

Part No.: 12-0130

Standard bracket for mounting on shaft or coupling.

Note: Just bracket, no chain.

Part No.: 12-0016

For mounting on shaft or coupling. The V-bracket fits shafts with diameters 20-450 mm [0.8-17.7″]. The standard chain included can be used on shaft diameters up to 150 mm [6″]. Bracket width 18 mm [0.7″].

Note: Extension chains available for shafts larger than diameter 150 mm [6″] (Part No. 12-0319 for one extension chain; Part No. 12-0128 for set of extension chains)

Part No.: 12-0128

Makes it possible to align very large shafts. Extends the chain for shafts up to diameter 900 mm [35.4″], (2 x). Used with standard V bracket.

Part No.: 12-1012

Used when the space between coupling and machine is limited. Width: 12 mm [0.5″].

Notes: Includes thin chains and tightening tool.

Part No.: 01-1165

Allows axial displacement between measuring units to be able to rotate past projecting machine parts. For both E and D series.

Note: 2 screws M6x14 also needed (Part No. 03-0061). V-bracket and rods not included.

Part No.: 12-1008

Allows axial displacement between measuring units to be able to rotate past projecting machine parts (for XT Series only).

Part No.: 12-1010

The spherical feet can be placed in two different for adaptation to small or large shaft diameters. Used when the shaft cannot be rotated. Mounted with standard chains.

Part No.: 12-0137

Available in different designs, with or without magnets, measurement probe and turnable head, depending on measurement application.

Part No.: 12-0615

For alignment of flange/offset mounted machines.

Notes: Delivered in plastic case. For E-series.

Part Nos.: 01-0938,12-0059, 12-0324, 12-0660

Screwed together, rods are extendable; theoretically “unlimited”.
Length 30 mm [1.18″], (1 x) Part No. 01-0938
Length 60 mm [2.36”], (4 x) Part No. 12-0059
Length 120 mm [4.72”], (8 x) Part No. 12-0324
Length 240 mm [9.44”], (4 x) Part No. 12-0060

Part No.:  01-0777

Adapters mainly for mounting of detector D157, E8 or E9 and used for extruder measurements.

Note: Manufactured on request to your specified diameter up to 250 mm. 2 pcs included.

Part No.: 12-0768

Bracket for straightness measurement of bores with a width of down to 25 mm [0.99”]. For bores 80 mm – [3.15”–]. Magnetic feet holds the bracket safely also upside down. With positioning guide (extended on picture to the right). Guide can be removed.

Note: Designed to fit with rod adapter 12-0767 and detectors E8/E9.

Part No.: 12-0455

For bore straightness measurement. With magnetic feet. For bores between 120–250 mm [4.72”– 9.84”].

Part No.: 12-0543

For bore straightness measurement. With magnetic feet. For bores between 200–350 mm [7.87”– 13.78”], width min. 80 mm [3.15”].m [3.94”].

Part No.: 12-0510

For bore straightness measurement. With magnetic feet. For bores between 300–500 mm [11.81”– 19.68”], width min. 100 mm [3.94”].

Part No.: 12-0767

For detector E8/E9. With slidable target. For mounting of the detector on regular rods with 40 mm centre-to-centre distance. Can be used on Slide bracket (12-0768) or any other suitable bracket.

Part No.: 12-0885

Accessories for roll diameter 400–1300 mm [15.7–51.2”] used with roll alignment system.

Note: Only legs as on picture to the left included.

Part No.: 12-0901

For using the E290 Precision Level on diameters 55–800+ mm [2.16–31.50+ “].

Note: Includes 2 legs, 4 magnets and mounting screws.

Part No.: 12-0187

Used for mounting against shaft ends, flywheels etc. Laser beam can point from the bracket or through the bracket.

Note: With three super magnets.

Part No.: 12-0628

For attachment of D22 or D23 laser transmitters on the outside of the flange, on non-magnetic flanges.

Note: A custom adaptable diameter (18–38 mm) on request.

Part No.: 12-0787

Bracket for use with an ES-unit as laser transmitter. Clamping pin min. 20 mm [0.79″], clamping length 40 mm [1.57″]. It is also possible to turn the measuring unit to point the laser beam through the pin. This is for example useful when aligning bar feeders.

Note: Rods and measuring unit not included.

Part No.: 12-0568

Accessory mounting pin for laser transmitter D146. Makes it possible to mount the laser transmitter in the chuck of a lathe and point it towards the sub spindle. Clamping min. 20 mm [0.79”].

Part No.: 12-0203

Sliding table for tripod, magnet base with turnable head, sliding bracket, and monument brackets for parallelism measurement of rolls. Used with the D22, D46 and 2 tripods.

Notes: Detector E5 also needed.

Part No.: 12-0269

Used for D22 Swivel Laser Transmitter and D46 Angular Prism. Height 500-2730 mm.

Part No.: 12-0341

For stern tube measurement. Smallest diameter 250 mm [9.84″]. Includes extension beams and rods for diameters up to 1200 mm [47.24″].

Note: No detector included.

Part No.: 12-0046

Used when measuring squareness and parallelism. A penta-prism that deflects the beam 90° is integrated in an adjustable housing.

Notes: A. With the rotatable angular prism you can reach the detector at any height on a flange, or on a roll at any height. B. The beam is aligned with the detector using the sled.

Part No.: 12-0709

Makes it possible to mount a measuring unit in front of the D46 angular prism. Used for precision aligning the prism.

Note: 1. Support screws, only used with some detectors to put the PSD at the correct height/centre in front of the prism.
2. Screws for mounting on the D46. Hexagon wrench and two rods 60 mm also included as pictured.